A. Bradji1, and E. Holzbecher2
1Charles University, Prague, Czech Republic
2Weierstrass Institute for Applied Analysis and Stochastics WIAS, Berlin, Germany
The convergence of numerical solutions is mainly determined by the convergence order, which quantifies the improvement of the solution when the mesh is refined. In this paper we examine various differential equations and the convergence behavior of their COMSOL Finite Element solutions. The numerically observed convergence rates are compared with theoretical results, as far as these are ...
A. Dixon, and D. DiBiasio
Department of Chemical Engineering, Worcester Polytechnic Institute, Worcester, MA, USA
The multiphysics simulation package COMSOL was incorporated into a course in mathematical modeling for chemical engineers. Our implementation for the first year of using COMSOL in the course is described, and assessment results based on examinations and student survey results are presented and analyzed. The students appear to be learning how to operate the COMSOL program quite satisfactorily, but ...
P. Aguirre, F. Figueroa
Sensor Technik Wiedemann GmbH, Kaufbeuren, Bayern, Germany
Pressure Sensors are widely used in the automotive industry. Their main use is the dynamic monitoring of pressure inside combustion engines. To achieve a good signal accuracy, the design of pressure sensors can be improved with FEM calculations of stress and strains on the measuring cell depending on their geometry and material properties. The geometry is adapted according to a special ...
I. Mantilla, S. De Vicente
National University of Engineering, Lima, Perú
Polytechnic University of Madrid, Madrid, Spain
We formulate a new mathematical model of gas-solids mixing hydrodynamic flow  in a combustion chamber with a fluid bed system used in the combustion of mineral coal waste. This model in study is called Model Gas-Solids Mixing and it is constructed by averaging the conservation equations (mass and momentum) for a two-phase flow, which takes into account the existence of a small parameter rho in ...
D. Iber, D. Menshykau, P. Germann, L. Lermuzeaux[2,3]
D-BSSE, ETH Zurich, Switzerland, SIB, Basel, Switzerland
D-BSSE, ETH Zurich, Basel, Switzerland
Department of Bioengineering, University of Nice-Sophia Antipolis, Nice, France
Morphogenesis is a tightly regulated process that has been studied for decades. Previously we developed data-based mechanistic models for a range of developmental processes with a view to integrate the available knowledge and to better understand the underlying regulatory logic. In our previous papers on simulating organogenesis in COMSOL Multiphysics® we discussed methods to efficiently solve ...
D. Iber, D. Menshykau
D-BSSE, ETH Zurich, Basel, Switzerland
Organogenesis is a tightly regulated process that has been studied experimentally for decades. We are developing mechanistic models for the morphogenesis of limbs, lungs, and kidneys with a view to integrate available knowledge and to better understand the underlying regulatory logic. Organ size changes dramatically during development, and tissues are composed of several layers that may expand ...
University of Hartford, Hartford, CT, USA
Laser percussion drilling is widely used in the aerospace industry to produce cooling holes in jet engine components. This process is a thermal, contact-free process which involves firing a sequence of focused optical pulses onto a target material [1-4]. During each optical pulse, the central portion of the target area heats to a liquid then vapor state where the expanding gas produces a recoil ...
M. Puskarczyk, B. Jamieson, W. Jurczak
ABB Corporate Research Center, Kraków, Poland
The effects of sharp corners on the flux distribution in a ferromagnetic core are modeled using COMSOL Multiphysics® to determine the time-domain flux density for an applied field which is uniform in the non-corner section of the core. The frequency spectrum of the flux distribution is calculated for testing points through the corner and the effects of harmonic frequencies on the flux and loss ...
Utilization of COMSOL Multiphysics' JAVA API for the Implementation of a Micromagnetic Modeling and Simulation Package with a Customized User Interface
L. Teich, A. Hütten, C. Schröder
Department of Engineering Sciences and Mathematics, Computational Materials Science & Engineering (CMSE), University of Applied Sciences Bielefeld, Bielefeld, Germany
Department of Physics, Thin Films and Nanostructures, Bielefeld University, Bielefeld, Germany
One of the big advantages of COMSOL Multiphysics is the possibility to implement user-defined partial differential equations (PDE) which can be coupled to COMSOL\'s predefined physics interfaces. However, using the tool’s standard user interface requires manual implementation of the PDEs and a multitude of problem-specific parameters. This process is not just error-prone but also very time ...
N. Alcheikh, C. Ayela, I. Dufour
Univ. Bordeaux, IMS Lab, Pessac, France.
Electrostrictive polymers have been of significant interest over the last years for energy harvesting. Principle is based on the conversion of a mechanical deformation into electricity. The stored energy basically depends on the mechanical strain induced into an electrostrictive polymer by the mechanical resonant vibration of a microcantilever supporting the electrostrictive layer. In this work, ...