B. Marmo, and B. Carruthers
Reactec Ltd., Edinburgh, United Kingdom
The onshore wind turbine industry must overcome many technical, commercial, and environmental difficulties. A significant element for planning consent is operational noise. Acoustic limits are strictly enforced and can lead to near-neighbour complaints as well as contractual disputes. Reactec have diagnosed, analysed and solved a problematic tonal resonance for a major wind turbine generator ...
V. Pavelko, I. Pavelko, M. Smolyaninovs, H. Pffeifer, M. Wevers
Riga Technical University, Riga, Latvia
Catholic University Leuven, Leuven, Belgium
A problem of damage prediction in aircraft structure and its non-destructive evaluation is very important for aircraft structural health assessment. The analysis of the features of direct impact of thin-walled laminate component of aircraft was performed by COMSOL Multiphysics software. Mainly the GFRC and CFRC laminates were selected in form either thin separate plate or sandwich structure. The ...
ACOUSTICS@MBD CONSULTANTS, LLC, Westborough, MA, USA
There is a practical interest among composite materials manufacturers to high-speed accurate non-destructive evaluation (NDE) technology for voids inspection when these voids are natural components of such complex structures like resin insulated layer of double-sided copper-clad laminates. Model based design (MBD) of NDE system is one of principal solutions for voids inspection in such composites ...
C. Van der Woude, and S. Narasimhan
University of Waterloo, Waterloo, ON, Canada
This paper presents a study of a wind turbine subjected to wind and seismic loading, carried out using COMSOL Multiphysics. The dynamic properties and response of wind turbine structures are of interest, as recent developments in wind energy have led to the design and construction of increasingly large and flexible turbine structures. A typical turbine structure model was created in ...
Dinex Emission Technology A/S, Middelfart, Denmark
Exhaust noise must meet legislation targets, customer expectations and cost reduction which call for design optimization of the exhaust systems in the design phase. One solution is to use 3 dimensional linear pressure acoustics and calculate the transfer matrix of the muffler. The transfer matrix is the basis for calculating either the insertion loss or transmission loss of a muffler. The 3D ...
E. Nesvijski[1,2], R. Sahul
Western New England College, Springfield, MA, USA
TRS Technologies, State College, PA, USA
Finite element analysis (FEA) is a modern tool for exploration of new horizons in science, technology and engineering. Different computer software such as ANSYS, ABACUS, PZFLEX and COMSOL Multiphysics® based on FEA are used for modeling and simulation of acoustic phenomena, for design of new and optimization and improvement of existing acoustic engineering systems. This work presents application ...
G. Campa, E. Cosatto, S. Camporeale
Politecnico di Bari, Bari, Italy
Ansaldo Energia, Genova, Italy
A hybrid technique based on the use of the FEM and the transfer matrix method is used to identify the frequencies at which thermoacoustic instabilities are expected and the growth rate of the pressure oscillations at the onset of instability. The Helmholtz equation is used to model the combustion chamber and the classical ?-? formulation for the flame model is adopted. The gas turbine combustion ...
Investigation on Sensor Fault Effects of Piezoelectric Transducers on Wave Propagation and Impedance Measurements
I. Buethe, C.-P. Fritzen
University of Siegen, Institute of Mechanics and Control Engineering-Mechatronics, Siegen, Germany
For active Structural Health Monitoring (SHM), one popular sensor type is the piezoelectric wafer active sensor (PWAS) due to its multi-purpose application as actuator and sensor and its low cost. It is used to generate a wave field, which interacts with the structure and is recorded by a second set of PWASs. This method is called acousto ultrasonics. The change in wave field from transducer ...
Dynamic Characterization and Mechanical Simulation of Cantilevers for Electromechanical Vibration Energy Harvesting
N. Alcheick, H. Nesser, H. Debeda, C. Ayela, I. Dufour 
Univ. Bordeaux, IMS Lab, Pessac, France
Energy harvesting from ambient vibrations has become an interesting topic for powering wireless sensor networks. Resonant microdevices based on MEMS have become of central importance at low frequency. The power produced at resonance is at least one order of magnitude larger than off frequency power since the largest strain is obtained at resonance. In order to obtain large strain for efficient ...
Mitsubishi Turbocharger & Engine Europe, Almere, The Netherlands
This study presents a rotordynamic analysis of a rotor on hydrodynamic bearings using COMSOL Multiphysics®. In this paper, the complexity of the model is gradually increased. Starting point of the analysis is the modal analysis of the rotor in free-free conditions. A Reynolds model is set up to predict the film pressure distribution under shaft loading. Due to the cross coupling terms of the ...